Jet Edge’s High Pressure Pump Chillers are the perfect match to your high-pressure intensifier pump. The chiller cools the hydraulics of the pump while the closed loop system continuously chills and recycles the water without discharging to the drain. The cooler water temperature improves pump performance and maximizes seal life. The range of units allows you to select the right chiller size for your pump and environment.
Pre-piercing of holes for All Waterjet Cutting Systems
The pneumatic drill adds additional efficiency by allowing for quick piercing, reaming, and tapping without moving the work piece. The drill can be adapted to all waterjet systems. Standard features such as hydraulic feed, exhaust collector, PLC interface module, built-in soft start and remote advance/retract porting make this a valuable addition.
Free running rpm of 3,300/drills 2” material maximum
The Permalign XP Cutting Head is designed to be used with the OmniJet XP to optimize performance and reliability. The cutting head is rated for pressures up to 75,000 psi (5,170 bar), orifice sizes range from 0.003-0.023 in (0.076-0.58 mm) and nozzle sizes from 0.020- 0.065 in (0.51-1.65 mm) ID. This combination handles small, intricate cuts as well as thick bevel cuts requiring higher abrasive and water flow rates.
Cutting head length 10.0-14.0 in (254-356 mm)
Operating water pressure maximum 75,000 psi (5,170 bar)
The OmniJet Waterjet Cutting Head’s lightweight and compact size offers versatility in multi-directional water jet cutting applications. It is designed and tested for pressures up to 60,000 psi and orifice sizes ranging from .003 to .020 inches. The cutting head has a fail-safe valve design and the orifices are pre-mounted in a set-screw style retainer making them easy to change with an Allen wrench. The OmniJet has been rigorously tested under high-duty cycle conditions.
Cutting head length 8.88-10.54 in (22.4-26.7 cm)
Operating water pressure maximum 60,000 psi (4100 bar)
Orifice range 0.003-0.045 in (0.076-1.1 mm)
Multi-directional cutting applications with various mounting options
The OmniJet XP is designed and tested for pressures up to 85,000 psi (5,900 bar) and orifice sizes ranging from 0.003-0.045 in (0.07621.14 mm). The high pressure cutting head stabilizes the water stream prior to entering the orifice. The pressure rating makes it perfect for cutting thick materials at high pressure.
Cutting head length 10.25 in (260 mm)
Operating water pressure maximum 85,000 psi (5,900 bar)
Orifice range 0.003-0.045 in (0.076-1.1 mm)
Multi-directional cutting applications with various mounting options
Jet Edge’s High Flow Abrasivejet supports an abrasive flow of up to 3.5 lbs/minute (1.59 kg/min) and is capable of delivering up to 7.2 gpm (27.3 L/min) of ultra-high pressure water. It is ideal for cutting thicker materials such as reinforced concrete walls or for separation cutting of steel plate or pipes.
Nozzle Length 4 in (102 mm)
Water Flow Rate 7.2 gpm (27.3 lpm)
Orifice range 0.023-0.042 in (0.058-1 mm)
Operating water pressure 55,000 psi (3,800 bar) max
The Aquavision® Di guides users through the process from job set-up to production. It is fully networkable, allowing part programs to be generated offline and easily transferred to the system’s hard drive for production. The rugged construction protects the controller and hosts extensive cutting and user interface features.
Real time diameter/kerf compensation
High-speed cornering
Single parts, mirroring, rotation, plate alignment
Backup along entire program path with real-time part trace
Jet Edge’s patented Dual Pressure Valve is a remotely mounted valve that allows waterjet operators to control water pressure independently of the intensifier pump. This enables operators to run a number of tables or cutting stations at various pressures.
In low-pressure piercing applications, the Dual Pressure Valve can increase productivity by allowing operators to reduce and raise water pressure without having to wait for the intensifier pump to drop to the lower pressure or rise to the higher pressure. The Jet Edge Dual Pressure Valve will operate with any manufacturer’s waterjet pump, cutting head, or cutting system, and is fully configurable for pressure change ratios.
Patented design
Connection points are standard 60,000 psi-type
Pneumatically operated
• Adaptable to any manufacturers pump, cutting heads or cutting systems
Designed for Coatings Removal and Surface Preparation
Jet Edge’s Robotic Swivel directs ultra-high pressure (UHP) water through a rotating manifold containing sapphire orifices or fan tip apertures to produce a concentrated water stream. Water pressure is regulated by adjusting the output of the UHP pump and water flow is regulated by the quantity and size of orifices used. Typical applications include preparation for recoating or repainting, stripping corrosion, coating overspray, paint scale, rust, parts cleaning and degreasing, part carrier cleaning, mold release residue, and much more.
Cutting head length with OmniJet & Manifold 20.25 in (51.4 cm)
Operating water pressure maximum 55,000 psi (3,800 bar)
The IP60-75 is our straight-to-the-point waterjet. You’ll be able to cut your application’s material and time spent on the job. It is perfect for moderately intense cutting projects. With the ability to run three 0.010″/0.030″ orifice/nozzle combinations, a 1.5 gpm flow rate, and a dynamic pressure of 55,000 psi, this pump will not let your application down.
But don’t worry! We continue to support you.
See our upgraded model, the HERO 50 with Jet Smart controls.
WATERJET INTENSIFIER PUMP
High Velocity Stream of Ultra High Pressure Water
The IP60-30 is designed for shops that desire the reliability of a hydraulic intensifier pump, but have limited power. This pump is capable of producing 0.6 gpm (2.3 lpm) of UHP water at a continuous operating pressure of 55,000 psi. It includes a hydraulic accumulator to provide smoother hydraulic pressure, reduce spikes, and prolong hydraulic pump life.
Jet Edge’s eco-friendly Closed Loop Filtration System reduces water and sewage costs, prevents the introduction of hazardous materials into drainage systems, and eliminates the need for a drain. The waterjet table overflows into a settling weir and the used garnet is settled out before entering the filtration system. The clean water is sent through an In-Line Chiller (sold separately) to remove the heat from the machining process. Clean and chilled water is delivered back to the high-pressure pump.
The Edge X-3 Mid Rail Gantry 3-axis water jet cutter is the no-nonsense workhorse of the Jet Edge line. Its 3-axis cutting capabilities excel at high-speed waterjet cutting and abrasivejet cutting and offers a slew of customization options. Paired with a Jet Edge HERO Series UHP Pump you have a committed cutting team!
3- axis cutting with water only or abrasive
Multiple Configuration Options to increase productivity
But don’t worry! We continue to support you.
See our upgraded model, the HERO 50 with Jet Smart controls.
WATERJET INTENSIFIER PUMP
High Velocity Stream of Ultra High Pressure Water
The IP60-50 Waterjet Intensifier Pump is your intro to pumps. Dependable and easy to maintain, it has the ability to cut and trim a large array of materials including heatsensitive, delicate, and tough substances. This Intensifier Pump is perfect for robotic, mobile, and motion system cutting applications. Jet Edge can provide an engineering analysis and customized solution to meet your application needs.
Rated pressure: 60,000 psi (4,100 bar)
UHP flow rate: 1.0 gpm (3.7 lpm)
Max rated orifice size: 0.015 in (0.38 mm)
Single piston, dual plunger intensifier with tie rod design
The Edge X-5 delivers 5-axis waterjet cutting precision that is capable of taper free bevel cutting to 60°. Choose a Permalign Arrow SL abrasivejet for cutting complex 3-D parts in the densest specialty alloys or the OmniJet Arrow SL waterjet for water only 5-axis cutting. Controlled with the fully networkable Aquavision DI a host of options to custom configure it to your operation’s needs are available. Coupled with a Jet Edge HERO Pump, your system is ready for high volume 5-Axis Waterjet cutting!
Features the Permalign Arrow SL, abrasive cutting or the OmniJet Arrow SL, water only cutting for higher finish quality, faster cycle times and lower maintenance costs.
5-axis cutting head can cut bevels to 60° and eliminate tapers
Programable Z carriage with servo motor driven 12″ (304 mm) vertical travel height
Multiple Configuration Options including independently programmable Dual Z Carriages
